rcwpm (military m/d55342) www.vishay.com vishay dale revision: 22-nov-12 1 document number: 31010 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 thick film chip resistors, military/established reliability mil-prf-55342 qualified, type rm features ? fully conforms to the requirements of mil-prf-55342 ? established reliability - verified failure rate; m, p, r, u, s, v, and t levels ? construction is sulfur impervious against a high sulfur environment (astm b 809-95 test method) ? 100 % group a screening per mil-prf-55342 ? termination style b - tin/lead wraparound over nickel barrier ? operating temperature range is - 55 c to + 150 c ? for mil-prf-32159 zero ohm ju mpers, see vishay dales rcwpm jumper (military m32159) datasheet ( www.vishay.com/doc?31028 ) ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 notes ? dscc has created a series of drawings to support the need for 0201-sized produc t. vishay dale is listed as a resource on this drawing as follows: this drawing can be viewed at: www.landandmaritime.dla.m il/programs/milspec/listdwgs.aspx?doctype=dsccdwg . (1) continuous working voltage shall be or maximum working voltage, whichever is less. (2) characteristics: k = 100 ppm/c; l = 200 ppm/c; m = 300 ppm/c. (3) mil case size 0705 and eia case size 0805 are dimensio nally the same. mechanical specifications resistive element ruthenium oxide encapsulation epoxy substrate 96 % alumina termination solder-coated nickel barrier solder finish tin/lead solder alloy standard electrical specifications vishay dale ? model mil-prf-55342 style mil spec. sheet term. case size power rating p 70 c w max. working voltage (1) v resistance range ? tolerance % temperature coefficient (2) ppm/c rcwpm-0502 rm0502 01 b 0502 0.05 40 1 to 9.1 2, 5, 10 300 10 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-550 rm0505 02 b 0505 0.125 40 1 to 9.1 2, 5, 10 300 10 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-5100 rm1005 03 b 1005 0.20 75 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-5150 rm1505 04 b 1505 0.15 125 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-7225 rm2208 05 b 2208 0.225 175 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-575 rm0705 06 b 0705 (3) 0.15 50 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-1206 rm1206 07 b 1206 0.25 100 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-2010 rm2010 08 b 2010 0.80 150 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-2512 rm2512 09 b 2512 1.0 200 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-1100 rm1010 10 b 1010 0.50 75 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-0402 rm0402 11 b 0402 0.05 30 1 to 9.1 2, 5, 10 300 10 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-0603 rm0603 12 b 0603 0.10 50 1 to 5.6 2, 5, 10 300 5.62 to 22m 1, 2, 5, 10 100, 200, 300 rcwpm-0302 rm0302 13 b 0302 0.04 15 1 to 9.1 2, 5, 10 300 10 to 22m 1, 2, 5, 10 100, 200, 300 dscc drawing ? number vishay dale model term. power rating p 70 c w res. range ? res. tol. % temp. coef. ppm/c max. working voltage (1) v 07009 rcwp-0201 b 0.05 10 to 46.4 47 to 1m 1, 5 200 100 30 p x r
rcwpm (military m/d55342) www.vishay.com vishay dale revision: 22-nov-12 2 document number: 31010 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? for additional information on packaging, refer to the surface mount resistor packaging document ( www.vishay.com/doc?31543 ). (1) products with space level failure rates are only offered in packaging codes with esd overpack and labeling. for all other failu re rates, the esd pack codes are an optional type of packaging. (2) failure rates u and v require group a and b inspection ran on each production lot. (3) mil spec option 1, 2, and 3 part marking is not offered for the sl ash sheet 01, 02, 11, and 13 sizes. global part number information new global part nu mbering: m55342m02b10e0rwb (pre ferred part number format) mil style characteristics spec. sheet termination style value and tolerance failure rate packaging (1) special d55342 applies to style 07 (rm1206) only. m55342 applies to all other styles. k = 100 ppm l = 200 ppm m = 300 ppm (see standard electrical specifications table) b = pre-tinned nickel barrier, wraparound (see tolerance and multipliers table) c = non-er m = 1.0 %/1000 h p = 0.1 %/1000 h r = 0.01 %/1000 h u = 0.01 %/1000 h (2) s = 0.001 %/1000 h v = 0.001 %/1000 h (2) t = space level tp = tin/lead, t/r (full) tn = tin/lead, t/r (full), w/esd ul = tin/lead, t/r single lot date code s3 = tin/lead, t/r (1000 pieces) sv = tin/lead, t/r (1000 pieces), w/esd wb = tin/lead, waffle tray wa = tin/lead, waffle tray, w/esd wl = tin/lead, waffle tray, single lot date code s2 = tin/lead, t/r (500 pieces) su = tin/lead, t/r (500 pieces), w/esd s6 = tin/lead, t/r (300 pieces) st = tin/lead, t/r (300 pieces), w/esd blank = standard (dash number) (up to 1 digits) s = space level w/option 1 part marking (-97) (3) t = space level (-98) 2 = option 1 part marking (-20) (3) 3 = options 2 and 3 part marking (-30) (3) historical part numbering: m55342m02b10e 0r (will continue to be accepted) m55342 m 02 b 10e0 r wb mil style characteristics spec. sheet termination style value and tolerance failure rate packaging code resistance tolerance and multipliers tolerance multiplier value range ( ? ) 1 % 2 % 5 % 10 % dg j m 1 1 to 9xx e h k n 1000 1k to 9xxk f t l p 1 000 000 1m to 22m examples: 11d3 = 11.3 ? 1 % ? 10e0 = 10 k ? 1 % ? 332d = 332 ? 1 % ? 2f21 = 2.21 m ? 1 % ? 51g0 = 51 ? 2 % ? 10h0 = 10 k ? 2 % ? 33h0 = 33 k ? 2 % ? 22t0 = 22 m ? 2 % 15j0 = 15 ? 5 % ? 10k0 = 10 k ? 5 % ? 560k = 560 k ? 5 % ? 8l20 = 8.2 m ? 5 % ? 10m0 = 10 ? 10 % ? 10n0 = 10 k ? 10 % ? 2p70 = 2.7 m ? 10 % ? 8p20 = 8.2 m ? 10 % 55342m02 m b10e0 r w b
rcwpm (military m/d55342) www.vishay.com vishay dale revision: 22-nov-12 3 document number: 31010 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ? ? ? ? ? dimensions in inches (millimeters) vishay dale model mil-prf-55342 style mil spec. sheet a (length) b (width) c (height) d (top term) e (bottom term) rcwpm-0502 rm0502 01 0.055 0.005 (1.40 0.13) 0.023 0.003 (0.58 0.08) 0.015 0.003 (0.38 0.08) 0.010 0.005 (0.25 0.13) 0.015 0.005 (0.38 0.13) rcwpm-550 rm0505 02 0.055 0.005 (1.40 0.13) 0.050 0.005 (1.27 0.13) 0.020 0.005 (0.51 0.13) 0.010 0.005 (0.25 0.13) 0.015 0.005 (0.38 0.13) rcwpm-5100 rm1005 03 0.105 0.005 (2.67 0.13) 0.050 0.005 (1.27 0.13) 0.020 0.005 (0.51 0.13) 0.015 0.005 (0.38 0.13) 0.015 0.005 (0.38 0.13) rcwpm-5150 rm1505 04 0.155 0.005 (3.94 0.13) 0.050 0.005 (1.27 0.13) 0.020 0.005 (0.51 0.13) 0.015 0.005 (0.38 0.13) 0.015 0.005 (0.38 0.13) rcwpm-7225 rm2208 05 0.230 0.005 (5.84 0.13) 0.075 0.005 (1.91 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) rcwpm-575 rm0705 06 0.080 0.005 (2.03 0.13) 0.050 0.005 (1.27 0.13) 0.020 0.005 (0.51 0.13) 0.016 0.008 (0.41 0.20) 0.015 0.005 (0.38 0.13) rcwpm-1206 rm1206 07 0.125 0.005 (3.18 0.13) 0.063 0.005 (1.60 0.13) 0.020 0.005 (0.51 0.13) 0.015 0.005 (0.38 0.13) 0.015 0.005 (0.38 0.13) rcwpm-2010 rm2010 08 0.197 0.006 (5.00 0.15) 0.098 0.005 (2.49 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) rcwpm-2512 rm2512 09 0.250 0.005 (6.35 0.13) 0.124 0.005 (3.15 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) 0.020 0.005 (0.51 0.13) rcwpm-1100 rm1010 10 0.105 0.005 (2.67 0.13) 0.100 0.005 (2.54 0.13) 0.020 0.005 (0.51 0.13) 0.015 0.005 (0.38 0.13) 0.015 0.005 (0.38 0.13) rcwpm-0402 rm0402 11 0.039 0.003 (0.99 0.08) 0.020 0.003 (0.51 0.08) 0.013 0.003 (0.33 0.08) 0.010 0.005 (0.25 0.13) 0.010 0.005 (0.25 0.13) rcwpm-0603 rm0603 12 0.063 0.005 (1.60 0.13) 0.032 0.005 (0.81 0.13) 0.018 0.005 (0.46 0.13) 0.012 0.005 (0.30 0.13) 0.015 0.005 (0.38 0.13) rcwpm-0302 rm0302 13 0.034 0.004 (0.86 0.10) 0.021 0.003 (0.53 0.08) 0.013 0.003 (0.33 0.08) 0.007 0.005 (0.18 0.13) 0.008 0.005 (0.20 0.13) rcwp-0201 0.024 0.002 (0.61 0.05) 0.012 0.002 (0.30 0.05) 0.009 0.002 (0.23 0.05) 0.006 0.003 (0.15 0.08) 0.006 + 0.002 - 0.004 (0.15 + 0.05 - 0.10) d c a e b derating curve - 55 - 25 75 100 125 150 175 120 100 80 60 40 20 0 ambient temperature in c 70 rated power in % 050 25 cage code: 91637 and sh903
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
